Then plug the Wifi Data Logger into the port and be sure to secure it by tightening the black connector. RHI-1P(5-10)K-HVES-5G Operation & Troubleshooting, Arc-Fault Alarm Troubleshooting for RHI-1P(5-10)K-HVES-5G, Advanced Hybrid DSP Issues - Replacing the DSP Board, Export Power Set and FailSafe Configuration, MET_Comm-FAIL and RS485 Fail Troubleshooting, Modbus Communications for RHI-1P(5-10)K-HVES-5G-US, Solis String-Level RSD Troubleshooting Procedures, Solis-(75-100)K-5G Tigo MLRSD Transmitter Disabling, Solis-1P(5-10)K-4G SunSpec MLRSD Transmitter Disabling, RHI-1P(5-10)K-5G SunSpec MLRSD Transmitter Disabling, RHI-1P(5-10)K-5G Tigo MLRSD Transmitter Disabling, Solis S1-W4G-ST WiFi & Cellular Data Logger Set Up Guide, Solis S3-WIFI-ST Wi-Fi Data Logger Setup Guide, Solis DLS-W WiFi Data Logger Installation Guide, Solis Cellular Data Logger Installation Guide, Solis DLS-C Cellular Data Logger - Carrier Compatibility, WiFi Stick Not Working With WiFi Extender Network. Shows the connection status between the datalogger and the inverter. 1. Solis monitoring system is centered around photovoltaic power station, focusing on service operation and maintenance, Remotely controlled,adopting plug and play connection. If you would like to change your settings or withdraw consent at any time, the link to do so is in our privacy policy accessible from our home page.. Monitoring Accessory Configured But Still Won't Link? When configured correctly (see below), Solis invertors will send data about their performance every 5 minutes to code waiting to receive the data. 1. 3: Set a manual IP for the computer using the following information -, (The IP of the computer must be with 10.10.100.XXX range to configure the LAN stick). Start by pulling up the site on SolisCloud - tap "Plant" in the bottom left corner and then find the desired site in the . SolisCloud Step 2: If it is a new data logger, please configure it first, then click the " Willi configure". The setup process for the SolisWifiData Logger is fairly similar to the Cellular Data Logger's process. Yes my data logger also glows red as well, does appear to be a LED keepalive in the unit to show its still transmitting data to the mothership. Victor is the author of this solution article. 2.4 GHz. Michael is the author of this solution article. Solarman Data Loggers (4-pin only) DLS-W: WiFi only data logger; DLS-L: LAN only data logger; DLS-C: 4G cellular only data logger; Solis is no longer selling these products in the US; Our distributors likely still have stock of these products but we are not promoting them; Solarman loggers do not support remote settings changes or firmware updates Router signal strength is low 4. Connect to the datalogger - AP_XXXXXXXXXX 3. Did you get a response from Ginlong? We use cookies to try and give you a better experience in Freshdesk. Open navigation. SolisCloud App helps you manage PV plant: 1. Solis S1-W4G-ST WiFi & Cellular Data Logger Set Up Guide; Solis S3-WIFI-ST Wi-Fi Data Logger Setup Guide; Solis DLS-W WiFi Data Logger Installation Guide; Solis Cellular Data Logger Installation Guide; Solis DLS-C Cellular Data Logger - Carrier Compatibility; Replacing a Solis Data Logger; WiFi password changed Go to your web browser - Input 10.10.100.254 4. Connect one end of an ethernet cable to LAN stick, 2: On the computer, click on the Network Connections and select the Local Connection. Step 5: Long press the Reset button for 5 seconds until the yellow and green LEDs are quickly flashing. Scan the bar code on the logger [note: a cellular logger is shown in the photo but it has the same scanning process as the, You should see a message that says "Bound Successfully" and now you will need to set up the logger on the local, settings and then connecting to the network that starts with "AP" - this is the. Interaction, Climate Change, Sustainability & on Properties, select internet protocol IPv4(TCP/IPv4). If you run through the setup wizard and are still having problems I suggest you contact them. Please provide the following information as well: Ginlong Technologies Co., Ltd.No. Screenshot of the Status page in the configuration interface. Help us improve this article with your feedback. This is the same data as can be sent to the ginlogmonitoring.com website for centralised data collection. Note: the logger is unable to connect to anyWiFinetwork that uses symbols in the password. It used to come back eventually but sometimes I went up to the attic and just unplugged it from the inverter for a second and then put it back in. I've been in contact with the team at . Required fields are marked *. How do you connect Solis? I had to go up to the attic and actually point the antenna towards my router. Note that all scripts use Python 3. If the WIFI stick shows the inverter but you don't have data on the monitoring portal follow these steps: If it is not pingable verify the router password again. Step 3: Manually fill in the datalogger SN or Scan the SN on the datalogger. Ginlong Solis is one of the world's recognised manufacturers of string solar inverters. This is to (1) ensure you have the correctWiFipassword and (2) ensure there is a strong enoughWiFisignal at the inverter for there to be a stable connection. 1. Internal DC Short: In the inverter head, or the wirebox? Verify the address is set to "1". I will ask AGL for a replacement. on solis S3-WIFI WiFi Stick Datalogger Installation Guide, solis GPRS Stick Datalogger Instruction Manual. Gua rpida de instalacin del sistema de monitoreo para Mxico y Centro Amrica. cordless phone, concrete wall, PV panel and metal wall, to ensure the communication quality. Otherwise, the communication quality may be affected. This should serve as a reminder to manually save your drafts if you wish to keep them. Press the button for 5 seconds to reset, 2 red lights are on and off at the same time, https://www.youtube.com/watch?v=nUjcDcY8-Ws, Solis DLS-G GPRS Datalogger setup and troubleshooting, Solis RHI HMI Update German Documentation. Step 2: Input the information about the plant as required. Connect your laptop to the Solis Wi-Fi network - this has a name which looks like "AP-xxxxxxxxx" 3. WiFi Instructions - Solis inverters are designed to last longer! AGL replaced it free of charge. It may also be affected by lighting storms. Wi-Fi trensmitting power: 802.11b/g/n: +20dBm/+18dBm/15dBm (Max) Data collection intervals: 5 minutes (adjustable:1-20 minutes) Preferences setting: Web server/Serial AT instruction. or, which is default value. The